List view Grid view Set filters on results Remove all filters

5-tube Nixie Clock V2 (DIY Kit, with copper top)

A limited edition version of our 5-tube clock.

Fitted with four IN-8-2 in place of the usual IN-14 tubes and solid copper machined top and base panels.

Features:
All interaction using IR proximity sensors - no buttons or remotes.
Single alarm
12/24 hour display
Display dim on/off times
GPS sync input possible
Seconds tick on/off
Variable seconds on/off
IR link to sync multiple clocks into one extended display
Low power less than 2W

The kit includes all parts required to build and use the clock, including a US power supply and USB lead. Complete PCB assembly, case part sanding and polishing skills required. You can find the assembly instructions over at http://www.lasermad.com/forums/viewforum.php?f=22

5-tube Nixie Clock V3 (DIY Kit, with Perspex and Paxolin case)

Functionally identical to our IN8-2/19 coppertop clock but much more affordable thanks to the lower cost nixies and featuring a Perspex cylindrical case with solid paxolin end caps.

Features:
All interaction using IR proximity sensors - no buttons or remotes.
Single alarm
12/24 hour display
Display dim on/off times
GPS sync input possible
Seconds tick on/off
Variable seconds on/off
IR link to sync multiple clocks into one extended display
Low power less than 2W

Fitted with one IN-15 and four IN-12 nixies the PCB is fully visible through the clear plastic case and held in place by two solid machined paxolin end caps. There are no external controls, all functions being controlled by our infrared proximity control system.

The kit includes all parts required to build and use the clock, including a USB power supply and USB lead. Complete PCB assembly, case part sanding and polishing skills required.

The assembly instructions can be found at http://www.lasermad.com/forums/viewforum.php?f=23

NOTE the photographs show the earlier Teak ended version, this clock is identical except the cylinder ends are made of paxolin (Similar to Bakelite).

5-tube Nixie Clock V1 (DIY Kit, with paxolin top)

The original paxolin cased version of our 5-tube clock with four IN-14 numeric nixies and one IN-19V symbol nixie as the centre colon which alternates between '+' and '-' symbols every second, the case has the appearance of Bakelite when polished/finished correctly.

Features:
All interaction using IR proximity sensors - no buttons or remotes.
GPS time sync 2400/4800/9600BPS
Short-term time backup on power loss
IR data link copies time and settings to other clocks nearby
Data link can chain up to 3 clocks together into a single display
Single alarm
Display dim on/off settings
Time calibration
Individual tube brightness calibration
Seconds tick
Random seconds tick
Fade/ripple/plain display modes
Cathode cleaning routine
Low power, less than 2W and can be powered from a standard USB port

The kit includes all parts required to build and use the clock, including a power supply and USB lead. Complete PCB assembly, case part sanding and polishing skills required.

The assembly instructions can be found on our website - http://www.lasermad.com/forums/viewforum.php?f=13

Personalized Engraved Mens Watch Steampunk Gear Watch Man Watch Brown Leather Band Groomsmen gifts or Father of the bride gift.

Personalized Engraved Watch comes with personalized hand engraving with the option to customize to your engraving needs with initials or date for only a little extra, see examples below!

This is a Steampunk influenced watch with a clear back. Made of stainless steel and has a gorgeous genuine Brown leather band.

Transparent dial with skeleton design gives you the most fashionable point of view.
Stainless steel watch case makes the watch more durable.
High quality leather band gives you a new classic definition.

Engraving Options:

Option 1-
1- Watch - Glass Back or engraving of a Gear on glass back (See picture #1 to see example of what the Gear engraving will look like) If you do not specify it will be plain
1 -Gift box included but NOT engraved

Option 2-
1- Watch -Glass Back
1- Gift box engraved (please see below for examples or picture #5)

Option 3-
1- Watch -Watch with custom engraving: INITIALS OR DATE!! .(that is all that will fit) Please send note to seller at time of purchase with engraving request
1- Gift box engraved (please see blow for examples or picture #5)

****Please send note to seller at time of purchase with engraving request****
Watch engraving is small and can be initials or date only due to size limits.



Some example phrases for the Gift Box engraving include:
Father of the Bride
Groom & wedding date
Best man/ Groomsman with name & date
#1 Dad or Grandfather or Uncle

Mother of the Bride
Bride & wedding date
Maid of Honor /Bridesmaid with name & date
#1 Mom or Grandmother or Aunt

I love you
Happy Birthday
Name & date

Don't forget to message us with your engraving request!

*Note* with hand engraving we try our best to center your request but center may vary slightly

Specs(approx):
Case diameter approx : 42mm
Case thickness approx: 14mm
Band Length (included case) approx: 7-8.5"L
Band Width approx: 20mm
Band Thickness approx: 4mm
Band Material: Leather
Weight: 132g (Stainless Steel:185g)
Water resistant: 3 ATM, not suitable for swimming, shower.


Please remember.
Please keep the watch away from magnets to avoid stopping the watch by keeping moving parts from working.
Please wind up the watch before every use.

Quality is Collectible and Wearable.

For a box please check these out the link below or look at my store.
https://www.etsy.com/listing/123842471/cardbaord-watch-box-with-insert-for
GIFT WRAP AVAILABLE.
https://www.etsy.com/listing/129003474/gift-wrap-option-for-our-items-only?ref=v1_other_2

INSTRUCTIONS
To use the watch: first, pull the knob and rotate to the correct time. Next, push the knob back in and wind clockwise for 15-20 rotations. Then put on your wrist and wear. The winding will give you many hours of run time but the motion of wearing it will keep it going longer. It is all mechanical and has no battery.

SHIPPING.
I offer international shipping but have no control over your country"s time frames or taxes you may be charged. I fill out the customs paperwork completely and accurately. Please check your local rules for answers to those items.
INTERNATIONAL SHIPPING PLEASE READ.
SHIPPING FIRST CLASS MAIL CAN TAKE UP TO 4 WEEKS TO DELIVER. PLEASE UNDERSTAND THAT BEFORE ORDERING. IF YOU WANT PRIORITY SHIPPING WHICH IS FASTER PLEASE CONTACT ME.

BY PURCHASING THIS ITEM AND HAVING IT SHIPPED OUT SIDE THE USA YOU ARE AGREEING TO UNDERSTAND THE TIME OF SHIPPING AND THE FACT YOU MAY INCUR CUSTOMS AND OR DUTY TAXES AND CHARGES BY YOUR COUNTRY. THE SELLER IS NOT RESPONSIBLE FOR THESE.


ALSO ABOUT SHIPPING
I try to ship these as soon as I can. I always set the shipping time to show the actual time before I ship so please do not purchase an Item that states 2 weeks to ship and expect it to ship the next day as It can not happen that way. 99% of the time I ship way early but you can not count on that. You get a shipping notification when I print the label to ship.

**gift boxes shown with engraving as example only, normal purchase comes with gift box minus engraving**

5-tube Nixie Clock V3 (Ready assembled with Perspex and paxolin case)

Functionally identical to our IN8-2/19 coppertop clock but much more affordable thanks to the lower cost nixies and featuring a Perspex cylindrical case with solid paxolin end caps. LED tube backlighting is currently available in a choice of blue, purple or amber.

Features:
All interaction using IR proximity sensors - no buttons or remotes.
Single alarm
12/24 hour display
Display dim on/off times
GPS sync input possible
Seconds tick on/off
Variable seconds on/off
IR link to sync multiple clocks into one extended display
Low power less than 2W

Fitted with one IN-15 and four IN-12 nixies the PCB is fully visible through the clear plastic case and held in place by two solid paxolin end caps. There are no external controls, all functions being controlled by our infrared proximity control system..

This is a ready to use clock, including a USB power supply and USB lead.

Operating instructions are here: http://www.lasermad.com/forums/viewtopic.php?f=24&t=111

NOTE the photographs show the Teak ended version, this clock is identical except the cylinder ends are made of paxolin (Similar to Bakelite).

Nixie OXO board DIY Kit, round IN-7 Nixies Included

Note: This is a DIY construction kit, not a finished board. This kit will include the 9 nixie displays needed for assembly.

The first and only Nixie-powered OXO (tic-tac-toe / noughts and crosses) in the world.
No plugs, Induction coils power the pieces right through the board.
A neat desk toy which takes up much less space than our chessboard but still very playable.

Supplied with five '0' (zero) pieces and four 'X' (Plus) pieces, '0' goes first and then take turns placing pieces anywhere you want on the board, they'll light up as soon as you put them down.

Back in a new easier to build through hole part design with IN-4 and IN-7 nixies as the 'O', only 40 of this version will be made available due to the limited number of parts available. These symbol nixie tubes are now in short supply and once they're gone, that's it. Game over.

Kit contents:

All PCBs and electronic components
4x IN7 nixies
5x IN4 nixies
10x Piece bases
Paxolin case parts and engraved board top - you'll need to fill in the engravings with a paint of your choice.
'Wall wart' power supply.

You'll need to supply sandpaper, paint for the engraved board and to colour the piece bases, basic tools including a good quality soldering iron and patience. You'll find the assembly instructions over at http://www.lasermad.com/forums/viewforum.php?f=26

Steampunk Watch cufflinks Watch Movements Cuff Links Watch Gear Cuff Links Gift for Him Mens gift ideas Birthday Gift for Husband

This listing is for Men's Steampunk cuff links. Two identical vintage non working watch movements are 3/4 inch long and about 1/2 inch wide (15mm x 12mm) . Perfect to wear to work, a wedding or give as a gift. If you have any questions please feel free to ask.
They come in small organza gift bag.
Here is same more cufflinks : https://www.etsy.com/shop/TimeJewelry1?section_id=17784190&ref=shopsection_leftnav_5

I ship worldwide via Priority insured mail ( UkrPochta)
All orders have tracking numbers and they are well trackable in the most countries.
Delivery time to USA is about 14-16 business days, and all order are trackable by USPS.com

5-tube Nixie Thermometer V2 (DIY Kit, with brass top)

A limited edition version of our 5-tube thermometer.

Fitted with heavy solid brass machined top and base panels only 40 of these will be available in total, shared between kits and ready built thermometers.

Features:
5 nixies including 3 digit and 2 symbol tubes
All interaction using IR proximity sensors - no buttons or remotes.
Displays temperature/humidity
Celsius/Fahrenheit/Kelvin display
Internal or external sensor readings
Includes an external sensor kit
Fade/ripple/plain display modes
Cathode cleaning routine
Low power, less than 2W and can be powered from a standard USB port

The kit includes all parts required to build and use the thermometer, including a US 2-pin power supply and USB lead. Complete PCB assembly, case part sanding and polishing skills required.

The assembly instructions are identical to our V1 thermometer and can be found on our website - http://www.lasermad.com/forums/viewforum.php?f=10

Nixie Chessboard DIY Kit, round IN-7 Nixies Included

Note: This is a DIY construction kit, not a finished board (the board is fairly simple to build, but you will still need to be confident soldering small parts). This kit will include all 32 nixie displays needed for assembly.

The first and only Nixie-powered chessboard in the world.
No plugs! Induction coils power the pieces right through the board.
A cool DIY project!

We've finally managed to secure a *small* quantity of IN-7 nixies and I've organised a few extra V1.5 printed coil PCBs to make use of them. This is the last time we expect the original version of the chessboard as seen in the 2012 videos to be available (though the electronics inside are newer). Supplied with 34x IN-7 and IN-7A nixies, through hole printed coil PCBs and all-brass bolts and thumbnuts.

No more days weeks spent winding coils, just assemble the PCBs and concentrate instead on an individual case finish for your board. Now includes a 12V power supply. Currently offered with a choice of IN-7 (round) or IN-15 (oval) pieces – just ask when placing your order. Future options may be limited as stock runs out - remeber these tubes haven't been made since 1991.
The symbols used to depict each piece may vary from the photograph depending on the availability of nixies. These symbol nixie tubes are now in short supply and once they're gone, that's it. Game over.

5-tube Nixie Clock V1 (assembled with paxolin top)

The original paxolin cased version of our 5-tube clock with four IN-14 numeric nixies and one IN-19V symbol nixie as the centre colon which alternates between '+' and '-' symbols every second, the case has the appearance of Bakelite.

Features:
All interaction using IR proximity sensors - no buttons or remotes.
GPS time sync 2400/4800/9600BPS
Short-term time backup on power loss
IR data link copies time and settings to other clocks nearby
Data link can chain up to 3 clocks together into a single display
Single alarm
Display dim on/off settings
Time calibration
Individual tube brightness calibration
Seconds tick
Random seconds tick
Fade/ripple/plain display modes
Cathode cleaning routine
Low power, less than 2W and can be powered from a standard USB port

Assembled and ready to use, It's approx. 80x145mm and 70mm high to the top of the tubes,

You can find the operating instructions here:

http://www.lasermad.com/forums/viewtopic.php?f=14&t=75

5-tube Nixie Thermometer V2 (Assembled and ready to use, with brass top)

A limited edition version of our 5-tube thermometer.

Fitted with heavy solid brass machined top and base panels only 40 of these will be available in total, shared between kits and ready built thermometers.

Features:
5 nixies including 3 digit and 2 symbol tubes
All interaction using IR proximity sensors - no buttons or remotes.
Displays temperature/humidity
Celsius/Fahrenheit/Kelvin display
Internal or external sensor readings
Includes an external sensor kit
Fade/ripple/plain display modes
Cathode cleaning routine
Low power, less than 2W and can be powered from a standard USB port

This is a ready to use version of our kit, built to order and it may be 1-2 weeks before despatch.

5-tube Nixie Clock V2 Ready assembled with copper top

A limited edition version of our 5-tube clock.

Fitted with four IN-8-2 in place of the usual IN-14 tubes and heavy solid copper machined top and base panels only 40 of these will be available in total, shared between kits and ready built clocks.

Features:
All interaction using IR proximity sensors - no buttons or remotes.
Single alarm
12/24 hour display
Display dim on/off times
GPS sync input possible
Seconds tick on/off
Variable seconds on/off
IR link to sync multiple clocks into one extended display
Low power less than 2W

The base plate will be engraved with the clock's serial number from 1/40 to 40/40.

This is a ready to use clock, including a US power supply and USB power lead.

Operating instructions can be found at http://www.lasermad.com/forums/viewtopic.php?f=22&t=103